Voltera Drill Head

Voltera V-One Drill Head Kit

Now Only

Creating double sided boards just got easier! Use this drilling attachment to make vias and through holes; then connect the top and bottom layers with rivets.

The drill mounts on the V-One just like the probe or dispenser but is externally powered. The operation is automated and surprisingly quiet. Just be sure to wear the safety glasses provided!

The attachment includes the following accessories:

  • 1 Drill bit set
  • 200 0.4mm Rivets
  • 200 1.0mm Rivets
  • 1 Sacrificial Layer
  • 10 2"x3" Substrates
  • 6 3"x4" Substrates
  • 1 Set of safety glasses
Add to cart

Voltera Drill Bit Set

For Only

A set of high precision drill bits, covering the most common drill bit sizes.

Just pop them in the V-One Drill with a 2.5mm hex key (not included) and start drilling.

The following sizes are included (2 of each): 0.70mm, 0.80mm, 0.90mm, 1.00mm, 1.60mm.

Add to cart

Voltera Sacrificial Layer / Drill Underlayment

For Only

To protect the V-One from any damage during drilling, mount this piece of FR1 on the heated bed and clamp your substrate on top.

The V-One Drill attachment will perforate your substrate but won't make it through this layer so your heated bed stays intact.

Only one is included, but don't worry, the sacrifical layer can be reused plenty of times.

Add to cart

Voltera 0,4 mm Rivets

For Only
Pack of 200

Do you need a way to connect the top and bottom layers? Rivets are the key!

Rivets are little copper tubes that make a mechanical connection between the top and bottom layer. We found rivets to be the easiest way to create vias. Be sure to pick up the corresponding rivet tool if you don't have one!

  • Inner Diameter - 0,4mm
  • Head Diameter - 0,9mm
  • Drill Size: 0,7mm
Add to cart

Voltera 1,0 mm Rivets

For Only
Pack of 200

Do you need a way to connect the top and bottom layers? Rivets are the key!

Rivets are little copper tubes that make a mechanical connection between the top and bottom layer. We found rivets to be the easiest way to create vias. Be sure to pick up the corresponding rivet tool if you don't have one!

  • Inner Diameter - 1,0 mm
  • Head Diameter - 2,2 mm
  • Drill Size: 1,6 mm
Add to cart

Voltera 2" x 3" FR1 Substrates

For Only
Pack of 10

When you start to run out of space in your design, migrate over from the small substrates to these.

These substrates are made of FR1 - which means they don't contain fiber glass. There is less wear on the drill bits and the dust is not harmful to your lungs.

Download the template and incorporate them into your design here

Add to cart

Voltera 3" x 4" FR1 Substrates

For Only
Pack of 6

When you start to run out of space in your design, migrate over from the small substrates to these.

These substrates are made of FR1 - which means they don't contain fiber glass. There is less wear on the drill bits and the dust is not harmful to your lungs.

Download the template and incorporate them into your design here

Add to cart

Voltera Punk Console Component Kit

For Only

The Punk Console circuit is an advanced tutorial to get you familiar with the V-One Drill attachment. Learn how to create a double sided board and turn the knobs to create music!

The kit contains:

  • 2 x Green LEDs
  • 8 x 1k Resistors
  • 3 x 0.01uF Capacitor
  • 2 x 500K Trimpots
  • 1 x 556 Timer
  • 1 x Piezo Buzzer
  • 1 x 9V Battery
  • 1 x 9V Battery Connector

Rivets and a V-One Drill are required.

Add to cart